Oil pan heater vs block heater, which is better?
Short answer
For most cars and trucks a coolant block heater is the better choice: it warms the engine block itself, and many vehicles sold in cold regions already have one. An oil pan heater warms only the oil in the pan; it's a cheaper add-on that needs no draining, but it only works on a metal pan (magnetic ones only on steel, not aluminum), and it helps less in severe cold.
Safety first. Never put a pad or magnetic heater on a plastic oil pan or any surface that can't take heat: Kat's says its pads can get hot enough to burn a person or melt an item. Route the cord so it can't touch hot or moving parts, and remove a magnetic heater and unplug any heater before you drive. If you see oil leaking near the pan, fix the leak before adding a heater there. Installing a coolant block heater means draining and opening the cooling system: unless you know what you're doing, have a mechanic do it.
On this page
Step by step
- 1
Check for a factory block heater first
Look for a three-prong plug behind the grille or bumper or coiled under the hood, or an 'engine block heater' or 'engine coolant heater' section in your owner's manual. If you have one, use it before buying anything else.
- 2
Find out what your oil pan is made of
Hold a magnet to the bottom of the pan. If it sticks, the pan is steel and either a magnetic or a stick-on pad heater can work. If it doesn't, the pan is aluminum (or plastic): a magnetic heater won't hold (Engineer Fix, Rick's Free Auto Repair Advice). A stick-on silicone pad needs a smooth metal surface (Phillips & Temro), and no heater goes on plastic (Kat's).
- 3
Pick the heater for how cold it gets
Where it regularly hits 0°F (-18°C) or colder, a coolant heater (factory, freeze-plug or lower-hose type) is the stronger option; Engineer Fix calls coolant-side heaters the more powerful solution for severe cold. An oil pan heater is a reasonable supplement, or a stand-in for milder cold or for equipment with no coolant heater.
- 4
Size a pad heater by oil capacity
Pad heaters run from about 50 to 1,000 watts. Phillips & Temro's 2014 chart pairs its 125-watt pad with 1.5 to 4 quarts of engine oil and its 250-watt pad with 4.5 to 12 quarts. Check your manual for your engine's oil capacity.
- 5
Install a stick-on pad on clean, bare metal
Kat's instructions: clean and sand the spot to bare metal, degrease it (not with gasoline or acetone), warm the pan by running the engine, press the pad on and roll out air pockets, seal the edges with high-temperature silicone, and tie the cord up away from hot or moving parts.
- 6
Plug in before you drive, unplug before you leave
Like a block heater, a pan heater only works while it's plugged in. Put it on a timer so it runs for the few hours before you leave, and unplug it before you start the engine.
The short version
| Coolant block heater | Oil pan heater | |
|---|---|---|
| What it warms | Engine coolant, so the block, heads and oil | Only the oil in the pan |
| Typical power | About 700 watts (Ram’s: 6.5 amps at 110 volts) | About 50 to 1,000 watts; 125 or 250 for car-size pans on Phillips & Temro’s chart |
| Fits | Most engines; many cold-region vehicles have one from the factory | Metal pans only. Magnetic: steel only. Stick-on pad: smooth metal (steel or aluminum). Never plastic. |
| Install | Drain coolant; freeze-plug, lower-hose or tank type (Rick’s) | Magnetic: stick it on. Pad: clean, sand, stick, seal (Kat’s) |
| Best for | Regular cold at 0°F (-18°C) and below | A supplement, milder cold, equipment and engines that can’t take a coolant heater |
Why a block heater usually wins
A block heater (also called an engine coolant heater) sits in the cooling system and warms the coolant, which surrounds the cylinders and heads. The whole engine starts warmer, and the oil warms with it. Engineer Fix calls coolant-side heaters a more powerful solution for severely cold climates, and Rick Muscoplat of Rick’s Free Auto Repair Advice says a freeze-plug (core plug) heater is the most effective type because it sits right in the coolant.
A pan heater warms the bottom of the engine only. A magnetic heater touches a small patch of pan, and Engineer Fix says much of its heat is lost to the outside air. Rick’s argues warm oil in the pan doesn’t reach the top of the engine until it cranks anyway.
If your car already has a block heater, use it: see how long to plug in a block heater.
When an oil pan heater makes sense
- No block heater and you don’t want to drain coolant. A pad or magnetic heater needs no draining or hose cutting.
- As a second heater in severe cold. A pan pad warms the oil while a coolant heater warms the block; the two don’t conflict. Phillips & Temro sells pads for oil pans, transmission pans, gearboxes and hydraulic tanks.
- Equipment with a metal pan. Tractors, generators and other machines without a coolant heater can take a pad sized to their oil capacity.
Magnetic vs stick-on pad
| Magnetic | Stick-on silicone pad | |
|---|---|---|
| Pan material | Steel or cast iron only; won’t hold on aluminum (Engineer Fix, Rick’s) | Any smooth, flat metal surface (Phillips & Temro) |
| Install | Clean, flat, paint-free spot (Engineer Fix) | Sand to bare metal, degrease, apply, seal edges with high-temp silicone (Kat’s) |
| Driving | Remove before driving (SlashGear) | Stays on; unplug and stow the cord |
| Example | Kat’s 1155X, 200 watts (SlashGear) | Zerostart pads, 50 to 1,000 watts, thermostat-controlled (Phillips & Temro) |
Phillips & Temro’s pads include a thermostat that holds them at 170 to 200°F (77 to 93°C), with higher-temperature 270 to 300°F versions also sold.
Where the sources disagree
- Whether pan heaters are worth it at all. Rick’s calls them a joke on modern engines running 0W or 5W oil and says many don’t have enough wattage. Phillips & Temro and Kat’s sell them for faster cold starts and less wear. We side with “a coolant heater first; a pan heater as a supplement or fallback.”
- How long to plug in. No pan-heater maker we checked publishes a time. Block heater guidance is 3 to 4 hours (CAA-Quebec); use that as a starting point.
Related winter answers
Common follow-up questions
Is an oil pan heater as good as a block heater?
Usually not. A block heater warms the coolant inside the engine, so the block, heads and oil all start warmer. An oil pan heater warms only the oil in the pan, and much of a small magnetic heater's output is lost to the air (Engineer Fix). It's still better than nothing on an engine that can't take a block heater.
Do magnetic oil pan heaters work on aluminum pans?
No. A magnet only sticks to steel or cast iron, so a magnetic heater can't be used on an aluminum pan (Engineer Fix, Rick's Free Auto Repair Advice). Rick's also says it won't sit flat on a pan with cooling fins. For a smooth aluminum pan, use a stick-on silicone pad instead.
Can I put an oil pan heater on a plastic oil pan?
No. Kat's says not to install its pads on plastic or any surface that can't withstand the heat, and Phillips & Temro says its pads go on smooth metal surfaces only. If your pan is plastic, a coolant block heater is the option.
How many watts should an oil pan heater be?
It depends on how much oil the pan holds. Phillips & Temro's chart pairs 125 watts with about 1.5 to 4 quarts and 250 watts with about 4.5 to 12 quarts. Kat's magnetic heater (model 1155X) is 200 watts (SlashGear). For comparison, Ram's factory block heater draws 6.5 amps at 110 volts, roughly 700 watts.
How long should I plug in an oil pan heater?
None of the heater makers we checked publish a time for pan heaters. For block heaters, CAA-Quebec says 3 to 4 hours before driving is enough. Starting a pan heater on a timer a few hours before you leave is a sensible default; leaving it on all night mostly costs electricity.
Can I use both an oil pan heater and a block heater?
Yes. They warm different things and don't conflict. Each needs its own grounded outlet capacity: a 700-watt block heater plus a 250-watt pad is close to 1,000 watts on one circuit.
Are oil pan heaters worth it on a modern car?
Opinions split. Rick Muscoplat of Rick's Free Auto Repair Advice calls them a joke on modern engines: today's 0W and 5W oils already flow when cold, and warm oil in the pan doesn't reach the top of the engine until it cranks. Pad makers say warm oil flows better and cuts wear at startup (Phillips & Temro). If your car has or can take a coolant heater, that's the surer bet.
Do I have to remove a magnetic oil pan heater before driving?
Yes. SlashGear says magnetic and strap-on pan heaters are temporary and must be removed before driving. Stick-on silicone pads stay on the pan permanently; just unplug the cord and stow it.
Sources
- 1.Phillips & Temro: Zerostart Silicone Pad Heaters brochure (LIT0172P, March 2026)
- 2.Phillips & Temro: Electric Pad Heaters brochure (LIT0005A, 2014): oil-capacity chart
- 3.Phillips & Temro: Silicone Heating Pads
- 4.Kat's Heaters (Five Star Mfg): Installation Instructions for Silicone Hot Pads
- 5.Engineer Fix: Do Magnetic Block Heaters Work for Cold Starts? (Liam Cope, Dec 25, 2025)
- 6.SlashGear: 5 Block Heater Alternatives For Diesel Engines (Wilfred Nkhwazi, Jan 16, 2025)
- 7.Rick's Free Auto Repair Advice: Engine Block Heater (Rick Muscoplat)
- 8.CAA-Quebec: Engine block heater in winter: Is it necessary in Quebec? (updated Oct 28, 2025)
- 9.Ram 2500/3500 Owner's Manual (2022): Engine Block Heater
General information only, not a diagnosis. Your owner’s manual comes first. How we write these